Select Page

EQB160-20B Automotive Engine

DCEC EQB160-20B automotive engine is a 6-cylinders in line, 5.9 liter four-strokes engine with 102mm bore and 120mm stroke, equipped with BYC P7100 pump. DCEC EQB160-20B automotive engine comes with turbocharger and Air- Air intercooler, with a EURO II post-processor. The prime power at 2500RPM of DCEC EQB160-20B automotive engine is 160 HP.

As part of EMAC, DuraMac provides complete powertrain that integrated with DCEC engine, Fast-Eaton clutch, FAST-CAT transmission, DANA axle and Komman air suspension, while the electrification of automobile is the certain future, Duramac also get involved with EV powertrain system. We provide full life cycle services for all customers, from design to power system supply, from installation to commissioning, from after-sales service training to spare parts supply, from trouble shooting to overhaul technical support.

1.Lower fuel consumption: Originated from the United States advanced design and superior manufacture, lower 20% oil consumption than congeneric Chinese products.
2.Strong power, the design of exhaust bypass valve makes low speed performance more perfect and better dynamic performance.
3.Excellent reliability, Cylinder block and head using integrated design, to stop the engine leaking and oil leakage phenomenon, engine parts are Less 40% than other similar engine, greatly reduce the failure rate.
4.Lower maintenance and repair costs, Fewer parts quantity and lower use fault Make the engine comprehensive maintenance cost greatly reduced and maintenance time than similar type save 50%.
5.Excellent cold start performance, equipped with air suction electric preheater and 6.6 kw power starter, Completely improve the cold start performance of the engine. Through the arctic village-MoHe of China-36C extreme low temperature validation.

Technical Specifications

Basic Introduction of DCEC EQB160-20B Automotive Engine

Engine Model:EQB160-20B
Engine Type:6
Displacement:5.9 L
Rated Speed:2800 RPM
Aspiration Method:Turbocharged & Air-Air Intercooler
Emission Standard:N/A
Bore*Storke:102 mm * 120 mm
Packing Size(L*W*H):N/A
Wet Weight:413 Kg
Lead Time:15-30 Working Days
Payment Terms:T/T ,L/C
DCEC-Cummins-EQB-Automotive-Engine-620x350

Engine Model

Advertised Power

Peak Torque

No. of Cylinders

Displacement

Fuel System

EQB125-20125 HP @ 2800 RPM410 N.m @ 1500 RPM43.9 LBosch Pump
EQB140-20125 HP @ 2800 RPM502 N.m @ 1500 RPM43.9 LBosch Pump
EQB160-20A125 HP @ 2800 RPM550 N.m @ 1600 RPM65.9 LBosch Pump
EQB160-20B125 HP @ 2800 RPM565 N.m @1500~1600 RPM65.9 LBYC P7000 Pump
EQB160-20C125 HP @ 2800 RPM570 N.m @1500~1600 RPM65.9 LWeifu PW2000 Pump
EQB170-21125 HP @ 2800 RPM560 N.m @ 1300 RPM65.9 LBYC P7100/RQV-K Pump
EQB180-20A125 HP @ 2800 RPM610 N.m @ 1500 RPM65.9 LBosch Pump
EQB180-20B125 HP @ 2800 RPM610 N.m @ 1500 RPM65.9 LBosch P7100 / Weifu PW2000 Pump
EQB190-20125 HP @ 2800 RPM650 N.m @ 1400 RPM65.9 LBosch Pump
EQB190-21125 HP @ 2800 RPM640 N.m @ 1300-1500 RPM65.9 LBYC P 7100 Pump
EQB210-20A125 HP @ 2800 RPM700 N.m @ 1500 RPM65.9 LBosch Pump
EQB210-20B125 HP @ 2800 RPM700 N.m @ 1500 RPM65.9 LBosch P7100 / Weifu PW2000  Pump
EQB235-20125 HP @ 2800 RPM800 N.m @ 1600 RPM65.9 LBosch P7100 Pump
——END——

General Infomation of DCEC EQB160-20B Automotive Engine

Engine ModelEQB160-20BAdvertised Power125 HP @ 2800 RPM
Peak Torque565 N.m @1500~1600 RPMCurve&DatasheetFR 91935
Fuel SystemBYC P7000 PumpNo. Of Cylinders6
AspirationTurbocharged & Air-Air IntercoolerDisplacement5.9 L
Bore*Storke102 mm * 120 mmCPL Code Revision40193
Dry Weight 413 kgWet Weight 437 kg
Compression Ratio17.3:1

Installation Data of DCEC EQB160-20B Automotive Engine

Center of Gravity. Distance From Front Face of Block328 mm
Center of Gravity. Distance Above Crank Centerline(Above Crankshaft)155 mm
Maximum Bending Moment At Rear Face of Block1356 N.m
Maximum Crankshaft Thrust Bearing load limit- Intermittent load3781 N
Maximum Crankshaft Thrust Bearing load limit-Continuous load1780 N
Instantaneous Inertia At Rotating: (Without Flywheel) N/A
Emissions CertificationGB17691/GB14761
Idle Speed750±100 RPM
Maximum Non-Load Speed2750±50 RPM
Over Speed Performance (Within 15 Seconds)3750 RPM
The Clutch Torque @ 800Rpm380 N.m
Maximum Altitude At Which Continuous operation Is Allowed3000 m
Supercharger outlet Exhaust Pressure limit Value 614 kPa
Maximum Power of Exhaust Brake112 kW
——END——

Engine Performance Data Rated power of DCEC EQB160-20B Automotive Drive Engine

Rated PowerTorque PeakRated PowerTorque Peak
Engine Speed2500 RPM1500 RPMExhaust Temperature526 498
Oil Pressure400 kPa350 kPaFuel Consumption92.2 kg/hr18 kg/hr
The Air Flow14 kg/min8 kg/minCoolant Flow153 l/min95 l/min
The Flow Rate of Pressurized Air15 kg/min10.3 kg/minHeat Loss Coolant50.2 kW35 kW
Pressurized Air Pressure110 kPa81 kPa Heat Loss Air30 kW10 kW
The Exhaust Flow869.5 kg/hr498 kg/hrMechanical Loss of Power26 kW12 kW

Performance-Curve-of-EQB160-20-BYC-P7100-Engine-for-Vehicle

System Technical Data of DCEC EQB160-20B Automotive Drive Engine

Air Intake SystemMaximum Temperature Rise Between Ambient Air And Engine Air Inlet15
Maximum Intake Restriction With Dry Type Air Cleaner,With Clean Filter-Medium Duty2.9 (300) kPa (mmH2O)
Maximum Intake Restriction With Dry Type Air Cleaner,With Clean Filter-Heavy Duty3.7 (380)kPa (mmH2O)
Maximum Intake Restriction With Dirty Filter6.2 (635)kPa (mmH2O)
Turbocharged & IntercooledMaximum Intake Manifold Temperature-Second Level55
Maximum Intake Manifold Temperature-Three-Level50
Intercooler Cooling Temperature-Second Level25
Intercooler Cooling Temperature-Three-Level20
Maximum Allowable Pressure Difference Before And After Intercooling-Three-Level16.7 (125) kPa (mmHg)
Minimum Inlet Pipe Diameter Allowed-Three-Level75 mm
Exhaust SystemMaximum Back Pressure Imposed By Complete Exhaust System10.0 (75) kPa (mmHg)
Exhaust Pipe Size Normally Accepable75 mm
Maximum Static Bend Allowed For Turbocharger Exhaust FlangeN/A
Lubrication SystemLow oil Level Inclination Angle-Front Up35 º
Low oil Level Inclination Angle-Back Up35 º
Low oil Level Inclination Angle-Fuel Pump Side Up35 º
Low oil Level Inclination Angle-Exhaust Side Up35 º
Oil Sump Capacity-Upper Limit14.3 L
Oil Sump Capacity-Lower Limit12.3 L
Capacity of The Whole System16.4 L
Cooling SystemCoolant Capacity – Engine only9 L
Standard Thermostat (Modulating) Range83-95
Minimum Fill Rate ( Without Low Level Alarm)19 l/min
Minimum Coolant Expansion Space – % of System Capacity6%
Water Tank Capacity Without Water Expansion5 L
Maximum Coolant Pressure (Without Pressure Cap, Thermostat Closed)276 kPa
Maximum Degassing Time25 mins
Maximum Coolant Flow To Accessories37 l/min
Maximum Coolant Temperature Engine out100
Minimum Allows Pressure of Pressure Cap50 kPa
Minimum Recommended Coolant Temperature70
Common Operating Temperature Range of Fans With Fan Clutch93
Maximum Coolent Temperature For Engine Protection Control100
The Limit Environmental Temperature At Rated SpeedSecond Level 45 ;Three-Level 42
The Limit Environmental Temperature At Peak TorqueSecond Level 40 ;Three-Level 37
24V Electrical SystemMaximum Allowable Resistance of Cranking Circuit0.002 Ω
The Cold Start Current When Engine And The Clutch Separate12 V 500 24 V 250
Cold Starting SystemMaximum Unaided Cold Start Temperature120 RPM -12  
Maximum Aided Cold Start Temperature110 RPM -35  
Fuel SystemMaximum Fuel Return Resistance520 (mmHg)
Maximum Inlet Resistance of oil Pump With Clean Filter150 (mmHg)
——END——

Scopes of Supply of DCEC EQB160-20B Automotive Engine

Air Intake System1. Air Intake ManifoldExhuast System1. Exhuast Manifold
2. Water-air Intercooler2. Turbocharger
3. N/A3. Exhuast Elbow
Fuel System1. Fuel transfer pumpStarting System1. Starter motor
2. High-pressure fuel pump2. Starter rely
3. Fuel Filter3. N/A
Charging System1. Charging alternatorEngine Shut-Down System1. Engine fuel shut-off solenoid
Lubricating System1. Oil pumpCooling System1. Water pump
2. Oil filter2. Engine Fan
3. N/A3. Standard radiator
Power Output System1. FlywheelEngine Mounting System1. Engine Mouting Bracket
2. Standard flywheel housing2. N/A
Engine Auiliary Accessories1. Air compressor
2. Power steering pump
——END——

Optional Accessories of DCEC EQB160-20B Automotive Engine

Air Intake System1. Air Intake pre-heaterExhuast System1. Muffler & bellows
2. Air intake shut-off valve2. Flame trap
3. Air filter3. Spark arrestor type Muffler & bellows
4. Air intake pre-filter4. DPF system
5. Air filter alarm system5. N/A
Fuel System1. Coarse FilterStarting System1.Manual Magnetic DC Contactor
2. Fuel pre-heater2. Dual ears flywheel housing
3. N/A3. Spring Starter Motor
4. N/A4. Air Starter Motor
5. N/A5. Hydraulic Starter Motor
Lubricating System1. Oil pre-heater.Cooling System1. Silent Type Radiator
2. N/A2. Plateau Radiator
3. N/A3. Salt-Spray Resistant Radiator
4. N/A4. Coolant pre-heater
Power Output System1. ClutchEngine Mounting System1. Shock absorber pad
Engine Auiliary Accessories1. Hydraulic oil pumpControl System1. Can add mechanical accelerator pedal
2. Air conditioner compressor2. N/A
3. N/A3. N/A
——END——

As part of EMAC, DuraMac is Committed to providing reliable powertrain system to commercial vehicle manufacturers around the world, a sub-brand of EMAC group that focusing on automotive application. Based on dozens of world-class engine manufacturing resources in China, and as official exporting agent of Fast tranmission (Joint venture with Caterpillar AT tranmission), Dongfeng Dana axle and Komman air suspension, DuraMac provides one-stop solutions covers from pre-design to components supply, from installation to commissioning, from pre-sales communication to after-sales service support.
For more information of our industrial power system products, you are welcome to visit ConeMac homepage: www.sino-gen.com

Modifiable Components of DCEC EQB160-20B Automotive Engine

Air Intake System1. Installation position of air filterExhuast System1. Can modify installation position and direction of
2. Upgrade to  heavy-duty type air fitlerturbocharger
3. N/A2. Water-cooled exhuast manifold
4. N/A3. Water-cooled turbocharger
Fuel System1. Upgrade to fuel fitler that integrated with fuel transferStarting System1. 12V starter motor for 12v electric system
pump and fuel pre-hearter2. Upgrading to specified brand and speicifications of
2. N/Astarter motor
Charging System1. 12V charging alternator for 12v electric systemEngine Shut-Down System1. 12V solenoid for 12v electric system
2. Explosion-proof charging alternator2. Explosion-proof solenoid
3. Upgrading to specified brand and speicifications of3. N/A
charging alternator4. N/A
Lubricating System1. Oil Pan positionCooling System1. Can modify engine fan into blower fan or suction fan
2. Number of dipstick2. Can modify central position of engine cooling fan
3. Position of dipstick can choose from 6 positions3. Can choose type of engine fan from mechanical type or
4. Can modify oil filter to be remote installationelectric type
Power Output System1. Can modify size of flywheel housing and flywheel.Engine Mounting System1. Can modify engine mouting bracket.
2. Dual-ear flywheel housing (For twin-starter system)2. N/A
3. Some of models can modify flywheel housing into PTO3. N/A
integrated type.4. N/A
4. Engine have connecting port of PTOs, that able to5. N/A
provide power output.6. N/A
Engine Auiliary Accessories1. All of auxiliary system can choose specified brands and
specifications.
2. Additional auxiliary systems can be added for special
applications.
——END——

Note: All Above Data are Just for Referenece, All Data Might Change Without Notices or Update, Please Contact Our Sales Team to Confirm All Details Via WhatsApp or Email.

WhatsApp Online logo

Sales Team


Generator Engine - Mr. Haden Wu

Marine Engine - Mrs. Hailey Tang

Automotive Engine - Mr. Vin Hu

Industrial Engine - Miss. Bella Huang

Pump Engine - Miss. Zora Zhou

Sales Director - Mr. Jasper Lee      

Service Team


Technical Service - Mr. Vin Hu

Customer Service - Mrs. Wendy Fu

Contact EMAC Now!

11 + 7 =

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Subscribe to get the latest updates from www.dcec-engine.com

You have Successfully Subscribed!

Pin It on Pinterest