Select Page

DCEC QSZ13-C425-II Industrial Engine

DCEC QSZ13-C425-II Industrial engine is a 6-cylinders in line, 13 liter four-strokes engine with 130mm bore and 163mm stroke. Equipped with Electrically Control High-pressure Common Rail, engine comes with turbocharger and Air- Air Intercooler. The prime power at 1900RPM of DCEC QSZ13-C425-II Industrial engine is 425HP.
As part of EMAC, ConeMac provides industrial power pack solution that integrated with air intake, air exhaust, cooling system, control system, transmission and hydraulic accessories, We also supplying special products such as explosion proof engine, generator and water pump set, as well as ultra-low temperature condition engine power pack. We provide full life cycle services for all customers, from design to power system supply, from installation to commissioning, from after-sales service training to spare parts supply, from trouble shooting to overhaul technical support.

Coming Soon

Coming Soon

1. Using Cummins XPI ultra-high pressure fuel injection system, the fuel injection pressure is up to 2400bar; through precise combustion control, the lowest specific fuel consumption can reach 186g/kW.h, and the low fuel consumption area is wide and more fuel-efficient.
2. Optimize the configuration of the whole machine, lighter weight and more compact structure, the maximum output power can reach 500 kilowatts, the power is surging.
3. Integral all-steel piston design, cylinder block and crankshaft made of high-strength materials, can withstand super-high explosion pressure of 230bar, rigorous component test verification, higher engine strength, and excellent reliability.
4. Adopt Cummins electronic control intelligent module to monitor the running status of the engine at any time, precisely control the fuel injection, so that the engine can also think.
5. No need for any cold start auxiliary device, easy to start at -15℃ ambient temperature; with auxiliary device can start at -30℃.
6. The engine adopts an optimized design of combustion chamber and high-mounted piston ring, four-valve structure, low cylinder head airway swirl ratio, high injection pressure fuel system, and almost zero smoke, achieving a perfect combination of emissions and economy.

Technical Specifications

Basic Introduction of DCEC QSZ13-C425-II Industrial Engine

Engine Model:QSZ13-C425-II
Engine Type:6 Cylinders
Displacement:13.0 L
Rated Speed:1900 RPM
Aspiration Method:Turbocharged & Charge Air Cooled
Emission Standard:N/A
Bore*Storke:130 mm * 163 mm
Packing Size(L*W*H):N/A
Weight , Net Dry:N/A
Lead Time:15-30 Working Days
Payment Terms:T/T ,L/C
DCEC-QSZ13-C425-II-Industrial-Engine.webp
 

Engine Model

Engine Speed

Output Power

Torque

Bore*Storke

Fuel System

QSZ13-C380-III1900 RPM286 kW1440 N.m130 mm * 163 mmHPCR
QSZ13-C400-III1900  RPM298 kW1500 N.m130 mm * 163 mmHPCR
QSZ13-C425-II1900 RPM316 kW1590 N.m130 mm * 163 mmHPCR
QSZ13-C425-III1900 RPM316 kW1590 N.m130 mm * 163 mmHPCR
QSZ13-C450-II1900 RPM335 kW1685 N.m130 mm * 163 mmHPCR
QSZ13-C450-III1900 RPM335 kW1685 N.m130 mm * 163 mmHPCR
QSZ13-C475-II1900 RPM354 kW1780 N.m130 mm * 163 mmHPCR
QSZ13-C475-III1900 RPM354 kW1780 N.m130 mm * 163 mmHPCR
QSZ13-C500-II1900 RPM372 kW1872 N.m130 mm * 163 mmHPCR
QSZ13-C500-III1900 RPM372 kW1872 N.m130 mm * 163 mmHPCR
QSZ13-C525-II1900 RPM391 kW1965 N.m130 mm * 163 mmHPCR
QSZ13-C550-II1900 RPM410 kW2060 N.m130 mm * 163 mmHPCR
QSZ13-C575-II1900 RPM429 kW2155 N.m130 mm * 163 mmHPCR
——END——
 

General Infomation of DCEC  QSZ13-C425-II Industrial Engine

Engine ModelQSZ13-C450-IIFire Order1-5-3-6-2-4
Curve&DatasheetFR20444Displacement13.0 L
Compression Ratio17:01Bore*Storke130 mm * 163 mm
No. Of Cylinders6 CylindersPacking Size(L*W*H)N / A
Fuel SystemHPCRConfigurationD0C3005CX03
AspirationTurbocharged & Charge Air CooledRated Power335 kW @ 1900 RPM
CPL Code Revision3788Peak Torque2250 N.m @ 1100 RPM – 1500 RPM

Installation Data of DCEC QSZ13-C425-II Industrial Engine

Low Idle Speed700 ± 50 RPM
Maximum No Load Governed Speed2050 RPM
Maximum Overspeed Capability2625 RPM
Maximum Altitude For Continuous Operation5200 m
Maximum Torque Available At 700  RPM1200 N.m
Approximate Engine Weight – Dry1245 kg
Approximate Engine Weight – Wet1310 kg
Center Of Gravity From Front Face Of Block519 mm
Center Of Gravity Above Crankshaft Centerline201 mm
Rotation Inertia Of Complete Engine (Without Flywheel)1.48 kg.m²
Maximum Static Mounting Surface Bending Moment Rear Face Of Block1356 N.m
Maximum Static Bending Moment Of FAN21 N.m
Maximum Allowable Weight On Engine Support(+12g / -10g Overload)1500 kg
——END——

 

Engine Performance Data Rated Power of DCEC QSZ13-C425-II Industrial Engine

Rated PowerTorque PeakRated PowerTorque Peak
Engine Speed1900 RPM1200 RPMExhaust Gas Flow37.1 kg / min20.2 kg / min
Gross Power Output335 kW283 kWAir to Fuel Ratio32.421.7
Torque1685 N.m2250 N.mHeat Rejection to Ambient13 kW11 kW
Brake Mean EffectivePressure1629 kPa2175 kPaHeat Rejection to JacketCoolant155 kW131 kW
Piston Speed10.32 m / s6.52 m / sHeat Rejection to Exhaust201 kW162 kW
Friction Horsepower50 kW20 kWHeat Rejection to Fuel4.17 kW3.34 kW
Coolant Flow450 l / min290 l / minHeat Rejection to Aftercooler64 kW32 kW
Fuel Consumption66.7 kg / h53.5 kg / hTurbochargerCompressor Outlet208 kPa156 kPa
Intake Air Flow30.5 m³ / min16.4 m³ / minCharge Air Flow36.0 kg / min19.4 kg / min
Exhaust Gas Temp – DryStack378 535 TurbochargerCompressor Outlet166 146
——END——
 

Performance Data of DCEC QSZ13-C425-II Industrial Engine

Air Induction SystemWhole Air Intake Pipe Size (Recommendatory)200 mm
Charge Air Cooler Pipe Size(Recommendatory)115 mm
Maximum Temperature Rise Between Ambient Air And Engine Air Inlet11.1
Maximum Temp. Rise Between Engine Air Intake And Intake Manifold30
Maximum Intake Manifold Temperature (Unable To Result In Performance Loss At Sea Level)60
Maximum Intake Manifold Temperature For Engine Protection85
Maximum Intake Air Restriction (Heavy Duty Air Cleaner)—Clean Filter3.2 kPa
Maximum Intake Air Restriction (Heavy Duty Air Cleaner)—Dirty Filter6.2 kPa
Maximum Allowable Pressure Drop Across Charge Air Cooler and  OEM CAC Piping (CACDP)13 kPa
Exhaust SystemMaximum Back Pressure Imposed by Complete Exhaust System13 kPa
Maximum Allowable Static Bending Moment at Exhaust Outlet Flange27 N.m
Exhaust Pipe Size (Recommendatory)130 mm
Lubrication SystemOil Pressure @ Idle – Minimum89.6 kPa
Typical Oil Pressure Range – Warm Engine207-300 kPa
Total System Capacity (Standard Pan)45.42 L
Maximum Lube Oil Flow to All Accessories7.57 L / min
Cooling SystemCoolant Capacity (Engine Only)23.1 L
Engine Coolant Circuit Thermostat Opening Temperature82
Engine Coolant Circuit Thermostat Fully Open Temperature94
Maximum Coolant Temperature – Engine Out102
Minimum Operating Block Coolant Temperature71
Maximum Coolant Temperature for Engine Protection Controls107
Maximum Coolant Pressure(exclusive of Pressure Cap; Closed Thermostat at Maximum No Load Speed)407 kPa
Minimum Pressure Cap Rating at Sea Level103 kPa
Maximum Coolant Friction Head External to Engine75 kPa
Maximum Deaeration Time25 min
Minimum Fill Rate (Low Level Alarm Required for Most Engines)19 L / min
Maximum Coolant Expansion Space (% Total System Capacity)10%
Minimum Coolant Expansion Space (% Total System Capacity)6%
Fuel SystemMaximum Allowable Restriction(OEM Point .Clean Filter)13.5 kPa
Maximum Fuel Drain Restriction (Total Head) Before (or Without) Check Valve27 kPa
Minimum Fuel Tank Venting Requirement0.2 L / s
Maximum Fuel Inlet Temperature71
Maximum Heat Rejection to Return Fuel5.36 kW
Maximum Design Fuel Flow204 kg / h
Electrical SystemSystem Voltage24 V
Minimum Battery Capacity-cold Soak at -18 C (0 F) —Engine Only Cold Cranking Amperes900 CCA
Minimum Battery Capacity-cold Soak at -18 C (1 F) —Engine Only Reserve Capacity270 min
Cold Start CapabilityMinimum Ambient Temperature for Unaided Cold Start15
Minimum Ambient Temperature for Aided Cold Start (Intake Air Heater)30
——END——
 

Scopes of Supply of DCEC QSZ13-C425-II Industrial Engine

Cooling System1. Water Pump        Exhuast System1. Exhuast Manifold
2. Engine Fan2. Turbocharger
3. Standard Radiator3. Exhuast Elbow
Starting System1. Starter Motor        Fuel System1. Common Rail Fuel System
2. Starter Rely2. Fuel Filter
Lubricating System1. Oil Pump        Power Output System1. Flywheel
2. Oil Filter2. Standard Flywheel Housing
Air Intake System1. Air Intake Manifold        Charging System1. Charging Alternator
Engine Mounting System1. Engine Mouting Bracket        Engine Auiliary Accessories1. Air Compressor
Control System1. Ecu & Sensors        
——END——
 

Optional Accessories of DCEC QSZ13-C425-II Industrial Engine

Air Intake System1. Air Intake Pre-Heater        Exhuast System1. Muffler & Bellows
2. Air Intake Shut-Off Valve2. Flame Trap
3. Air Filter3. Spark Arrestor Type Muffler & Bellows
4. Air Intake Pre-Filter 4. Dpf System
5. Air Filter Alarm System5. N/A
Engine Auiliary Accessories1. Hydraulic Oil PumpControl System1. Can Add Engine Monitoring System, Contro System With Wiring Harness
2. Air Conditioner Compressor2. Can Add Self-Protection System That Integrated with Alarm System
Starting System1. Manual Magnetic Dc ContactorCooling System1. Silent Type Radiator
2. Dual Ears Flywheel Housing2. Plateau Radiator
3. Spring Starter Motor3. Salt-Spray Resistant Radiator
4. Air Starter Motor4. Coolant Pre-Heater
5. Hydraulic Starter Motor5. Jacket Water Heater
6. Remote Starting Function6. N/A
7. Lock Protection Function Of Starter Motor7. N/A
8. Manual Magnetic Dc Contactor8. N/A
Fuel System1. Coarse FilterLubricating System1. Oil Pre-Heater
Power Output System1. ClutchEngine Mounting System1. Shock Absorber Pad
——END——

Committed to Providing Stable and Reliable Premiem Power System for Global Construction Machinery Manufacturer Partners, ConeMac is A Sub-Brand of the EMAC Group that Focuses on Construction Equipment Application. ConeMac’s Ranges of Products Mainly Inclduing Marine Construction Engines Power Pack, Construction Equipment Gearbox, Gear Reducer, Explosion-Proof Engines, Generator Set and Water Pump Set for Mining, Oil and Gas Field. For More Information of Our Industrial Power System Products, You Are Welcome to Visit ConeMac Homepage: Conemac.cn

 

Modifiable components of DCEC QSZ13-C425-II Industrial Engine

Exhuast System        Charging System1. 12V Charging Alternator For 12V Electric System
1. Can Modify Installation Position And Direction Of Turbocharger2. Explosion-Proof Charging Alternator
2. Water-Cooled Turbocharger3. Upgrading To Specified Brand And Speicifications Of Charging Alternator
Power Output System1. Can Modify Size Of Flywheel Housing And FlywheelLubricating System1. Oil Pan Position
2. Dual-Ear Flywheel Housing (For Twin-Starter System)2. Number Of Dipstick
3. Some Of Models Can Modify Flywheel Housing Into Pto Integrated Type3. Position Of Dipstick Can Choose From 6 Positions
4. Engine Have Connecting Port Of Ptos, That Able To Provide Power Output4. Can Modify Oil Filter To Be Remote Installation
Cooling System1. Can Modify Engine Fan Into Blower Fan Or Suction FanEngine Auiliary Accessories1. All Of Auxiliary System Can Choose Specified Brands And Specifications
2. Can Modify Central Position Of Engine Cooling Fan2. Additional Auxiliary Systems Can Be Added For Special Applications
3. Can Choose Type Of Engine Fan From Mechanical Type Or Electric Type3. N/A
Fuel System1. Upgrade To Fuel Fitler That Integrated With Fuel Transfer Pump And Fuel Pre-HearterEngine Mounting System1. Can Modify Engine Mouting Bracket
Control System1. Ecu Can Setting To Different Control Mode, Including Can Communication, Analogue Control, Isc1,Isc2,Isc3 Speed Conrol Mode Etc
——END——

Note: All Above Data are Just for Referenece, All Data Might Change Without Notices or Update, Please Contact Our Sales Team to Confirm All Details Via WhatsApp or Email.

WhatsApp Online logo

Sales Team


Generator Engine - Mr. Haden Wu

Marine Engine - Mrs. Hailey Tang

Automotive Engine - Mr. Wells Luo

Industrial Engine - Mrs. Luna Fu

Pump Engine - Miss. Zora Zhou

Engine Parts-Miss. Nora

Sales Director - Mr. Jasper Lee      

Service Team


Technical Service - Mr. Vin Hu

Customer Service - Mrs. Wendy Fu

Contact EMAC Now!

5 + 5 =

Subscribe To Our Newsletter

Subscribe To Our Newsletter

Subscribe to get the latest updates from www.dcec-engine.com

You have Successfully Subscribed!

Pin It on Pinterest